My network:
  •  Twitter
  •  Ribbonfarm section
  •  Youtube channel
  •  Facebook
  •  Instagram
  •  Github
  •  Livejournal (rus)
  • Scihouse
  • Spaceway forum
  • Spaceway
  • Writing:
  • Random thoughts
  • Random stories
  • Hardware:
  • Sound camera (RF)
  • Timelapse camera
  • MicroBook reader
  • Multiband camera
  • Multiband camera (RF)
  • Tesla coils
  • Soviet calculator
  • 3D printer
  • Quadrotor UAV
  • Box of sunshine
  • Molten salt battery
  • LCD curtains
  • Software:
  • Aprom OS
  • METEOR M decoder
  • Spaceway
  • M.A.X. Remake
  • Rocket Land
  • Random games
  • Artwork & photo:
  • Time lapses
  • Concepts - Rhego
  • Concepts - Pella
  • Random Art
  • Lunar eclipse
  • Orbiter addons:
  • Collision SDK
  • Orbiter Shipyard
  • Shukra Station
  • OGLAClient
  • Orulex
  • OSH gallery
  • Shukra gallery
  • Orulex gallery
  • OGLAClient gallery
  • Ship Generator
  • Shipgen manual
  • Orbiter flight gallery
  •       Leave a comment:

    (Add 1 to the number (i.e. if it's 4589, type 4590) )
    (Прибавить 1 (т.е. если 4589, то вводить 4590) )

    I'm not sure which resistor are you talking about.
    If it's the one in the perfboard photos, then this is so out of date as to be irrelevant.
    18.04.2015 01:15 - Artlav

    Hello again!
    I see that you have used a 20k Ohms resistor in your circuit, what capacitor did you used to go with it?
    14.04.2015 16:16 - Alejandro

    Two columns in one direction align naturally, as long as the mechanics aren't too loose.

    Two adjacent columns going in opposite directions, however, are still an open problem.
    It's repeatable enough to align the central parts by a fixed offset in post-processing, but there are edges where things get non-linear. I'm thinking of making a sort of a correction table, by taking a picture of a grid.

    If that's what you were asking.
    09.02.2015 09:56 - Artlav

    You made a great system. I Working on a same concept by moving the sensor with servos.
    I have a question, How did you manage to rectify the offset of a pixel column to another?
    Have A nice day!
    09.02.2015 03:26 - Chyneuze

    The noise is RF in origin - what helped is wrapping the box in grounded foil, eliminating ground loops and putting the sensor in a shielded box of it's own.

    Light/reflection noise is not something i noticed or encountered, and painting it black will be tricky, since many "black" paints turn bright white in NIR. I'm not immediately aware of any paint that would be uniformly black across the entire spectral range of that camera.

    The code is too simple to be worth posting - drive the steppers, sense the light, write to the card. All three are there in Arduino's set of demos.
    08.02.2015 23:53 - Artlav

    I get what you are saying in regards to electrical noise

    If you make the inside of your box matte black, like all cameras are, you will notice a big difference in noise level and contrast.

    I'm working on one of these right now, the initial test camera obscuras I've built work WAY better when you all the internal surfaces black.

    Great project!

    Will you be posting your code???
    07.02.2015 14:35 - cyberteque

    @j: Not really. The sapphire window, peltier stabilised 3400nm one was the most expensive at about $57 equivalent.
    @Andre: They would be waaay too large. Sensor size is pixel size - the larger the sensor, the lower the resolution is.
    22.01.2015 22:34 - Artlav

    Photodiodes from IBSG...that could not had been cheap.
    22.01.2015 22:04 - j

    Hi, just a thought but have you tried using a solar cell as a sensor?
    The ones used on solar lamps work reasonably well, or you could also harvest them from old photoelectric smoke alarms.
    I found two nice 7mm2 diodes this way, good for several mA when put next to a TV remote.
    22.01.2015 21:50 - Andre

    @vimtut0r: I did, back in 2013 (the pages are quite a bit out of date). Simplifies the code a lot, makes the image somewhat cleaner.

    @The Lightning Stalker: Pieces of coloured glass, "hot mirror" window from a DSLR, UV filter glass, polished piece of silicon, and several others.
    22.01.2015 13:04 - Artlav

    Very cool project!
    Why don't you just place an ATTiny or something similiar right next to the OpAmp to reduce the signal length?
    22.01.2015 12:09 - vimtut0r

    What filters are you using for wavelength selectivity?
    22.01.2015 04:44 - The Lightning Stalker

    Well done!!
    06.09.2014 22:58-nixxon

    Thanks a lot!
    Ill let you know if it worked for me
    26.08.2014 01:48-Alejandro

    AD820 for the pre-rebuild stuff.
    AD8605 for the latest version.
    In my case i needed to measure sub-pA currents, thus the need for very low-offset op-amp.
    20.08.2014 11:30-Artlav

    Which op amp did you used?
    Im trying to build a green index sensor!
    14.08.2014 01:14-Alejandro

      ADSE 0.9.2   © 2005-2017,